Product Details:
|
Product Name: | BSPT & NPT 4'' Electric Pipe Threader 4"Pipe Threading Machine | Chaser Set: | 1/2"-3/4", 1"-2", 2 1/2"-4" |
---|---|---|---|
Motor Power: | 900w | Speed: | 22/10rpm |
Thread Type: | NPT Or BSPT | Package: | 1wooden Case/set |
G.W/N.W.: | 154/135KGS | Packing Size: | 93.5x59.5x60cm |
High Light: | 10 Rpm Electric Pipe Threader,Electric Pipe Threader 4",Aluminum Pipe Threading Machine |
BSPT & NPT 4'' Electric Pipe Threader 4"Pipe Threading Machine Heavy Duty And Aluminum Body
4'' Electric Pipe Threader BSPT & NPT Heavy Duty with Aluminum Body
4'' Pipe Threading Machine BSPT & NPT Aluminium Body with Heavy Duty Tripod Stand
4'' Electric Threader BSPT & NPT for Steel Pipe Materials with Aluminum Body
4'' Pipe Threader BSPT & NPT with Chaser Set, Aluminum Body & Heavy Duty Tripod Stand
4'' Threading Machine BSPT & NPT with Die Head, Tool Kit & Aluminium Body
Specification
Electric pipe threader 4"
Chaser set: 1/2"-3/4", 1"-2", 2 1/2"-4";
Motor power: 900w;
Speed: 22/10rpm;
Thread type: NPT or BSPT
Ductile iron made die head
Full aluminium body
With Heavy Duty Tripod Stand, English Instruction Manual, Threading Oil and Die Head, Chaser Set and Tool Kit
Package: 1 plywoode case/set
G.W/N.W.: 154/135KGS
Packing size: wooden case 93.5x59.5x60cm
Working principle of threading machine
Installation
1. Check if all parts and accessories are in good condition including tool bag, oil, tooth, tooth holder and support legs.
2. Lift the device and fix the legs, then tighten the screws of the legs evenly
The back head should be slightly higher than the hammer head to ensure the cooling oil flow.
3. Clean the oil from the teething and add some grease to the places of movement.
4. Make sure the machine is working properly before starting and make sure the oil is pumped.
5. Install each moving part when you want to move the machine to another work area. The dental head must be locked in place, and a short tube placed in the head.
Operation manual
1. Catch tubes
1) Expand the thread head to enter the tubes from the compressor shaft side.
2) At first close the rear head, then close the front head to catch the tubes, check the three jaws of the head from the front head and on normal use, jerk the knocking head toward yourself to lock the tube.
3) Move the front head in the opposite direction to unscrew the tube after completion.
4) If you are using a short tube so that it does not reach the back jaw, just insert the tube towards the head of the teeth and lock it with the teeth, then insert the supporting head to fix the tube.
2. Teething
1) Lift the cutter out of the way and bring the tooth head into the working position.
2) Turn on the switch to make the machine work. Apply pressure to the sliding handle until three or four threads are cut. Then release the sliding handle, the normal teething will be cut off automatically. When an appropriate amount of placements are cut.
3. Tube cutting
1) Put the pipe cutter in the working position.
2) Turn the sliding handle to make the pipe cutter to the point you want to cut.
3) Turn the cutter handle tightly.
4) Turn on the switch. Then turn the cutter handle slowly and tightly as it cuts from the tubes.
5) After cutting the tubes, release the cutter handle and raise the tube cutter.
4. Enlargement
1) Make the lathe head in the working position.
2) Lock the lathe head.
3) Turn on the switch. Adjust the slide knob to bring the lathe head into the tubes.
4) Cut off the electricity. Return the lathe head to its normal position
Application & Details:
Our service:
1 Genuine produces with excellent quality and competitive price.
2 Cooperating with the customers all over the world and knowing the markets very well.
3 After- Services will be highly-satisfied. Any problems and feedbacks will be answered in a short of time.
4 We can provide OEM
Contact Person: Mrs. YeGuiFeng
Tel: +86 85778256
Fax: 86-571-85778267