Choose the right pinch roller and knurl wheel and install them onto the roll grooving machine.
Put the pipe on the knurl wheel and pipe stands.
The pipe stands should be placed at the position of 3/4 length of pipe. Then adjust the pipe stands height to make sure the pipe are 1 degree lower than the horizantal level.
Tighten the relief valve, shake the hydraulic pump handle, let the pinch roller going downward until it touch the surface of pipe end. Rotate the limit nut down, make it contact with the oil pump top frame. Check the correct data of groove depth for different diameter pipes in the chart. For instance, if we roll groove on a 8 inch pipe, the depth will be 2.34mm. Calculate from the red start line, rotate the limit nut 2.34mm up, then turn the fastening nut down until it touch the limit nut and fix it. (One circle rotation on the limit nut is equal to 2.5mm) Rotate the side guide wheel to support the pipe. Release the relief valve.
Connect the power plug, turn on the switch to run the machine.
Tighten the relief valve again and pump the handle to start grooving. Continue to swing the handle until the limit nut reach the oil pump top (Please do not swing too fast). Allow the pipe to rotate additional one or two turns to make sure the groove is completed.
At last turn off the switch and release the relief valve knob. Rotate the guide wheel to make it away from the pipe. Remove the pipe and check the groove depth with a pipe groove measuring tape.
And our best seller one is manual pipe groover:
1) STG11A Manual pipe grooving machine for installed pipe grooving and mounted on power unit is one manual or power driven in-place grooving tool, it is specifically designed to be used either in place or with some Power Drives such as RIDGID 300, RIDGID 300C and REX threading machine. With the appropriate adapter, the tool can work with threading machine. customers choose the corresponding methods based on the different situation.
2) This manual grooving machine is designed for 3/4inch to 8inch carbon steel pipe. It covers range of pipe diameter, to solve the pipe problem in different diameter during maintains.
3) This grooving machine is only 12.4kgs (Tool weight includes the tool housing only), it is light, so it can be handled and operated easily.
4) This grooving machine is operated using a standard 27mm deep socket and square-drive ratchet. Ratchet is known as a mechanism consisting of a pawl that engages the sloping teeth of a wheel or bar, permitting motion in one direction only. There is one switch on the ratchet which makes the motion forward or backward.
5) This manual grooving machine is equipped with two pcs support arms and one pc power drive adapter, these parts makes manual groover mount on the power drive then to be an electrical roll grooving machine.
Choose the right pinch roller and knurl wheel and install them onto the roll grooving machine.
Put the pipe on the knurl wheel and pipe stands.
The pipe stands should be placed at the position of 3/4 length of pipe. Then adjust the pipe stands height to make sure the pipe are 1 degree lower than the horizantal level.
Tighten the relief valve, shake the hydraulic pump handle, let the pinch roller going downward until it touch the surface of pipe end. Rotate the limit nut down, make it contact with the oil pump top frame. Check the correct data of groove depth for different diameter pipes in the chart. For instance, if we roll groove on a 8 inch pipe, the depth will be 2.34mm. Calculate from the red start line, rotate the limit nut 2.34mm up, then turn the fastening nut down until it touch the limit nut and fix it. (One circle rotation on the limit nut is equal to 2.5mm) Rotate the side guide wheel to support the pipe. Release the relief valve.
Connect the power plug, turn on the switch to run the machine.
Tighten the relief valve again and pump the handle to start grooving. Continue to swing the handle until the limit nut reach the oil pump top (Please do not swing too fast). Allow the pipe to rotate additional one or two turns to make sure the groove is completed.
At last turn off the switch and release the relief valve knob. Rotate the guide wheel to make it away from the pipe. Remove the pipe and check the groove depth with a pipe groove measuring tape.
And our best seller one is manual pipe groover:
1) STG11A Manual pipe grooving machine for installed pipe grooving and mounted on power unit is one manual or power driven in-place grooving tool, it is specifically designed to be used either in place or with some Power Drives such as RIDGID 300, RIDGID 300C and REX threading machine. With the appropriate adapter, the tool can work with threading machine. customers choose the corresponding methods based on the different situation.
2) This manual grooving machine is designed for 3/4inch to 8inch carbon steel pipe. It covers range of pipe diameter, to solve the pipe problem in different diameter during maintains.
3) This grooving machine is only 12.4kgs (Tool weight includes the tool housing only), it is light, so it can be handled and operated easily.
4) This grooving machine is operated using a standard 27mm deep socket and square-drive ratchet. Ratchet is known as a mechanism consisting of a pawl that engages the sloping teeth of a wheel or bar, permitting motion in one direction only. There is one switch on the ratchet which makes the motion forward or backward.
5) This manual grooving machine is equipped with two pcs support arms and one pc power drive adapter, these parts makes manual groover mount on the power drive then to be an electrical roll grooving machine.
